PRO DI Series
PRO 248
PRO 248 is a dual channel active DI specially developed by UNiKA for electric guitar and electric bass. It is equipped with a 260KΩ over-impedance input terminal and a special isolation transformer, which can provide very rich harmonic and overtones for musical instruments.
OVERVIEW
- .Power by external +48V phantom power
- .Built-in UNiKA-PROTM EI30A10E isolation transformer
- .Use British OEP PT-4 1:1 audio pulse transformer in phantom power circuit
- .+48V status indicator on the upper cover
- .The input socket uses a pair of TRS jacks
- .Use a pair of TRS jacks as through out terminal
- .At 0dB input, the set load impedance is 260KΩ, which can clearly show the high frequency overtones , harmonic and graininess of electric guitars or electric bass
- .50Ω ultra-low impedance output, suitable for various types of mixers and pre-amp equipment
- .There is 0dB/-20dB input signal attenuation switch with status indicator
- .The output is equipped with a GND/LIFT switch
DESCRIPTION
PRO 248 is an active dual-channel DI box. Unlike traditional DI, PRO 248 uses +48V phantom power instead of the traditional 9V dry cell battery, so users can use it on the mixer or external phantom power supply. Power is supplied to PRO 248, the power supply circuit and the output signal line are shared, and no additional power cord is required. The +48V indicators are set on the upper cover. The +48V circuit specially selects the British OEP PT-4 pulse transformer.
PRO 248 has a pair of built-in UNiKA-PROTM EI30A10E 1+1:1+1 isolation transformers, which has a special copper foil layer and a dedicated ground layer, which allows this device to restore high signal/noise ratio and dynamic sound, and can avoid unnecessary leakage caused by radio frequency interference, ground interference and potential difference. PRO 248 is especially suitable for electronic musical instruments, recording studios and fixed installation projects by using mixers.
The PRO 248 uses two TRS sockets on the input, and two TRS through out are convenient for musician to pass the direct signal to the instrument amplifier. In addition, it is equipped with a 0/-20dB attenuation switch and LED indicator, which is suitable for various types of audio signals with high and low impedance. The output terminal is also equipped with a GND/LIFT button to quickly eliminate ground noise.
INPUT PAD ATTENUATION
The most widely used DI box is to connect electronic musical instruments, sound source of A/V equipment and computers, convert their output signals into balanced signals and then extend the transmission distance.
The most ideal state is to set the attenuator to 0dB position (button up) for musical instrument. For some other type of signals, you can press the button to make the signal is attenuated by 20dB to avoid clipping caused by signal overload.
When the button is pressed, the PAD indicator on the right will light up.
This attenuator acts on the input terminals of CH-1 and CH-2 at the same time.
The most ideal state is to set the attenuator to 0dB position (button up) for musical instrument. For some other type of signals, you can press the button to make the signal is attenuated by 20dB to avoid clipping caused by signal overload.
When the button is pressed, the PAD indicator on the right will light up.
This attenuator acts on the input terminals of CH-1 and CH-2 at the same time.
POWER SUPPLY
PRO 248 is an active DI box and requires +48V phantom power. It can work normally when it is powered, but no additional power supply is required. Just use balanced wires to connect the device to the mixer’s input channel, and turn on the +48V power switch of the mixer, similar to connect a condenser microphone to the mixer.
When the +48V power supply is suppling properly, the +48V ACTIVE indicator light on the upper cover will light up.
WARNING: Before connecting the device, do not turn on the +48V switch of the mixer.
When the +48V power supply is suppling properly, the +48V ACTIVE indicator light on the upper cover will light up.
WARNING: Before connecting the device, do not turn on the +48V switch of the mixer.
ELIMINATING GROUND LOOP NOISE
The built-in channel independent balanced isolation transformer has solved the potential difference leakage problem. When the system causes a ground loop due to poor wiring, the noise can be eliminated through the GND/LIFT button.
The GND/LIFT button determines whether pin 1 of the output XLR is grounded, grounded when it bounces, and disconnected from ground when pressed.
The GND/LIFT button determines whether pin 1 of the output XLR is grounded, grounded when it bounces, and disconnected from ground when pressed.
SPECIFICATIONS
PRO 248 | |||
---|---|---|---|
Circuit principle | Active low-noise op-amp with Transformer balance output | ||
Input connector | 2 x TRS | ||
Thru connector | 2 x TRS | ||
Input pad switch/indicator | 0/-20dB push button with LED | ||
Power supply | +48V Phantom power through output connector with LED indicator on top cover | ||
Output connector | 2 x Male XLR through ISO Transformer | ||
Output GND/LIFT switch | Shared push button | ||
Input impedance | 260KΩ / 0dB, 50KΩ/-20dB | ||
Output impedance | 50Ω | ||
Max. input level before clipping | +10dB | ||
Max Output level | +10dB | ||
Frequency response | 20Hz-20KHz, +0.05/-0.5dB | ||
S/N ratio @20Hz~20KHz un-weight | >95dB | ||
T.H.D. @1KHz 0dBV output | <0.02% | ||
Transformer Ratio | 1:1+1:1 | ||
Chassis | 1.6mm/1.2mm steel cabinet and chassis | ||
Surface finished | Durable complex painting | ||
Dimension (W x D x H) | 78 x 124 x 46 mm | ||
Weight | 0.66Kg | ||
Shipping weight | 0.69kg | ||
Packing per carton | 20pcs/14.40Kgs | ||
Shipping dimension per carton | 305 x 283 x 195mm |